I have noticed something strange going on the past weeks, that has changed. It seems if I have a program set for access requirements set to ANSI, the program is not showing up even if the user is set to ansi in the defaults. If I take the ANSI out of the access requirements, it shows up fine. I will use me as an example. In my Default Settings it reads:
Terminal Mode: Auto CP437 / ANSI (color) (mouse)
And I don't see any doors or programs that have an Access Requirement of ANSI.
with the same results. If I take out the Access Requiremnet of ANSI, all is fine and I can see the program. For now I have removed ANSI from the access requirements, so my users can play them, but I'm concerned what could be causing this. What module countrols this, so I can see if I don't have the latest one, or what could I have done since the latest update to cause this.
Re: Access Requirement On Externalsall is fine and I can see the program. For now I have removed ANSI
By: DesotoFireflite to All on Sun Feb 20 2022 09:53 am
I have noticed something strange going on the past weeks, that has
changed. It seems if I have a program set for access requirements set
to ANSI, the program is not showing up even if the user is set to ansi
in the defaults. If I take the ANSI out of the access requirements, it
shows up fine. I will use me as an example. In my Default Settings it
reads:
Terminal Mode: Auto CP437 / ANSI (color) (mouse)
And I don't see any doors or programs that have an Access Requirement
of
ANSI.
This sounds like a problem that was introduced recently (after v3.19b was release) and fixed on Feb-6: http://git.synchro.net/gitpushlog.ssjs#f5fed0b229e70b79a5ebb330af98a348ccb bfd6
with the same results. If I take out the Access Requiremnet of ANSI,
It's Synchronet itself (e.g. sbbs.dll for Windows).
I checked, and I have the one from 2/1/22 in there, and thats the last update I did. This is crazy man, all these issues.
I'm litterly at the point
of doing a fresh install, but I'm putting that off as a last resort.
I
downloaded last nights sbbs_run.zip, and sbbs_dev.zip, but I kept getting a Xaccesserror when starting the control panel, so I went back to the 2/1/22 that build that I saved. I'll wait till tomorrow and get a later build incase last nights is corrupt.
Re: Access Requirement On Externals
By: DesotoFireflite to All on Sun Feb 20 2022 09:53 am
I have noticed something strange going on the past weeks, that has
changed. It seems if I have a program set for access requirements set
to ANSI, the program is not showing up even if the user is set to ansi
in the defaults. If I take the ANSI out of the access requirements, it
shows up fine. I will use me as an example. In my Default Settings it
reads:
Terminal Mode: Auto CP437 / ANSI (color) (mouse)
And I don't see any doors or programs that have an Access Requirement
of
ANSI.
This sounds like a problem that was introduced recently (after v3.19b was release) and fixed on Feb-6: http://git.synchro.net/gitpushlog.ssjs#f5fed0b229e70b79a5ebb330af98a348ccb bfd6
with the same results. If I take out the Access Requiremnet of ANSI,
all is fine and I can see the program. For now I have removed ANSI
from the access requirements, so my users can play them, but I'm
concerned what could be causing this. What module countrols this, so I
can see if I don't have the latest one, or what could I have done
since the latest update to cause this.
It's Synchronet itself (e.g. sbbs.dll for Windows).
| Sysop: | Weed Hopper |
|---|---|
| Location: | Clearwater, FL |
| Users: | 14 |
| Nodes: | 6 (0 / 6) |
| Uptime: | 232:02:34 |
| Calls: | 55 |
| Calls today: | 1 |
| Files: | 50,127 |
| D/L today: |
35 files (4,430K bytes) |
| Messages: | 275,419 |